Rubber conveyor sidewall belts are specialized belt which have been used to transfer powdered or loosely spread materials transferring time is not tedious, the rubber conveyor belt manufacturers easily being damaged and worn. Consider a flat belt that can carry stuff along, however, when the belt is flat sometimes the material will slide over the sides. And that is when sidewalls would come in handy. These sidewalls are added rubber edging which has been stuck on the belt, and therefore when you are traveling up a hill or at an angle, your material will not be inclined to fall off. BEDROCK design them tough and firm due to the knowledge that materials must be safe and functioning well in mines or factory. Not all belts can withstand the task but these sidewall belts are designed to perform the task particularly in rough and tough conditions when other belts may not work. They assist in making things go without waste of material or introduction of hiatuses.
It is not just a rubber conveyor sidewall belt. It is made up of high rubber walls on each side such that the material does not spill out during those times when the belt jerks up the steep slopes or that lean forward and back on curves. These walls are not inflexible yet firm enough not to bend over rollers and pulleys. That is when you are going like the devil and that belt is turning, the weight, coal and gravel and grain will not come off. BEDROCK rubber sidewall belts are made by making layers of fabric that provide the steel cord rubber conveyor belt with strength and flexibility. This will enable them to carry heavy loads over a very long time without tearing or wearing out easily. That is one massive benefit: space-saving since the belt can be taken on steep slopes which cannot be easily managed by a flat belt. Moreover, less spills save time and money in cleaning and also less material wastage. To take an example, when you are where I am at a mine, one of our sidewall belts would be great to take a great load of rock up a hill and not miss a single piece. Rubber edges hold everything in place, and therefore workers do not need to clean spills or clear blockages that often occur. This also contributes to the increased safety of the whole process because loose powder will appear slippery on the floor and cause accidents.
The correct rubber conveyor sidewall belt may be difficult to choose. You must take into account the kind of materials you will be carrying, the weight of the materials and the steepness of the belt that will be necessary. Bedrock backs us with that since they understand much about various jobs and settings. An example would be when you have to haul a lot of weight like heavy rocks or metal pieces, then you would want a really tough conveyor belt which has an additional layer of fabric on the inside. However, when you are working with something lighter, like grains or sand, then perhaps it is the belt that should be more elastic and smoother on the surface. There is also the issue of temperature. Others are hot, or cold, very much so, in which case the rubber cannot crack or melt. BEDROCK designs belts which can resist everything on the outside thus they will work anywhere on you. The sidewalls too is a consideration of their size. The closer to a sidewalk end of the table, the greater will be the sidewall, on which to store material, and the larger a product that can be placed on one corner of it. The broader sidewall needs more support to prevent its sagging. BEDROCK has the ability to design the height and the thickness of these walls to meet your requirements. Sometimes the belt is forced to cross sharp curves or go around narrow curves. The belt, in this case, should be flexible, yet not easily ripped. Our belts, BEDROCK, are tested in flexing and stretch over a hundred times before they come out of the factory. The ease of maintenance and installation of belt would also be looked at. You will have to buy a new belt that you will always be replacing which will cost you more to replace and also when it is out of service.
In the process of seeking a rubber conveyor sidewall belt that are of high quality in your business, it is crucial to ensure that you find the support institution that will simply satisfy all your needs. These special belts are able to move materials over sharp inclinations or to secure material against spillage off the conveyor. This is why you require durable, long lasting and belts that ensure their usefulness even in hard conditions. We at BEDROCK produce and supply rubber conveyor sidewall belts of high quality to the most difficult materials handling. These belts are made of heavy rubber with thick sidewalls that assist in the safe transportation of materials. The design of BEDROCK belts is intended to absorb the impact of heavy loads and abusive operations in the batch plant, quarries, sand and gravel pits, cement operations, recycling plant and other manufacturing or industrial settings. When you acquire a belt at BEDROCK, you are not only acquiring a belt; you are also value added to the product since it has been tested to be able to hold on to any form of wear and tear. And ours is configured to help reduce or eradicate the belt run-out, thereby one less variable to consider during installation and use.
Rubber conveyor sidewall belts are apt to be used in unpleasant working environments including: mines, factories or excessive amounts of dust, heat and the like. In order to make these belts long-lasting, it is important to maintain them in a good condition. At BEDROCK we know that quality care is good because it makes our belts last longer and it saves you the cost of repairs. One, at all times check the belt by looking at it on the possibility of obvious wear or damage. Examine crack, tear or frayed sidewalls. When you are early with your troubles, when the belt has not been broken, then unless you are unlucky you are probably saving yourself further trouble with your engine. Otherwise, the rubbers get worn out quicker by dirt, wax and traces of materials. Use a weak cleaning agent only and avoid any exposure of the belt to any chemical substances that may damage the belt. Tension In the Belt The tension of belt is another significant checkup. A belt that is too tight or too loose might not only be worn in a shorter time, but even can be irritating to your conveyor because it drops off the pulleys. BEDROCK has easy to use guidance as well as tools that can be used to achieve such a tension.
With an established local leadership team and service network in Saudi Arabia, we offer end-to-end support—from product selection and installation guidance to ongoing performance tracking—ensuring prompt response, clear communication, and minimal disruption to your operations.
We measure our success by your operational outcomes. Through continuous follow-up, optimization, and a commitment to total value, we build strategic partnerships that help you reduce downtime, improve efficiency, and achieve sustainable growth together.
Backed by 16 years of specialized R&D and experience in national-level research projects, we develop conveyor belts that exceed industry standards in critical areas such as high-temperature and flame resistance, delivering reliability under the most demanding operational environments.
We don't just sell products — our experienced team in Saudi Arabia provides customized conveyor system recommendations based on your specific working conditions and industry challenges, ensuring optimal fit and long-term performance.
EN
